Xboard images12/18/2022 Tests:SCIF-FIFO: Test SCIF FIFO behavior, using SCIF3 and HSCIF3 on expansion I/O connectors.Tests:eMMC-8bit-width: Test the on-board eMMC with an 8 bit bus width.This 0x570 in Entry 0 means that the end address is 0x56ffffff.The lower 18-bits of "DCMPAREACRBx" means end address.This 0x540 in Entry 0 means that the start address is 0x54000000.The lower 18-bits of "DCMPAREACRAx" means start address.The bit 31 of "DCMPAREACRAx" is set to 1, this means the Lossy decomp feature is enabled.If you see the following strings, the firmware enables Lossy decomp feature.Īnd, we cannot use the memory area from 0x54000000 to 0x56ffffff as Linux system memory. * DTB: arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb (for R-Car M3-W) * DTB: arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb (for R-Car H3 ES2.0 and later) * DTB: arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb (for R-Car H3 ES1.x) Kernel v5.5 and older used different DTB names: The old boot loader on R-Car H3 ES1.0 does not support the above addresses, but you can use the following instead, depending on the bootloader version installed on the board. * DTB: arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb (for R-Car M3-N) * DTB: arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dtb (for R-Car M3-W) * DTB: arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dtb (for R-Car H3 ES2.0 and later) * DTB: arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dtb (for R-Car H3 ES1.x) Use a micro-USB cable to connect to "Debug Serial 0". Refer to Yocto page for steps necessary for running Yocto. Use SW9 ("Reset") to reboot the board when necessary.Ĭonfigure U-Boot to boot over TFTP + NFS or from a micro SD card Quickly hit any key to get into U-boot command prompt. NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0 NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0 NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570 NOTICE: BL2: QoS is default setting(rev.0.32) NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.9 Then you should see the following output in the terminal: Switch "SW23" to "ON" to switch the board on. Power on the board and go to U-Boot prompt Running dmesg | tail can help locating proper device.Īfter the successful connection, picocom should display:Īfter the successful connection, minicom should display: Replace DEVICE with the proper tty device name, for example /dev/ttyUSB0. Any standard terminal emulator program can be used. Windows driver and sources can be found on Silicon Labs website. On Linux, FT232 driver is included with kernel versions >=2.6.12. It is routed to SCIF2 in the R-Car H3 via a FT232 interface converter chip. CN25 ("DEBUG SERIAL-0") must be used on Salvator-X side. Use a microUSB cable to connect the Salvator-X board. The power supply should be able to provide 9 Amps. Use 12 V power supply with a 5.5 mm barrel plug. Refer to Yocto for steps necessary for making a Yocto image. This sections describes steps that are necessary to run a "Hello, World!" application using Yocto build. MICROSD-CARD SLOT (SDR104 100 MBYTES/S).QSPI FLASH 16MB QSPI (128 MBITS,80 MHZ,80 MBYTES/S)1 HEADER QSPI MODULE.HYPERFLASH 64 MB HYPER FLASH (512 MBITS, 160 MHZ, 320 MBYTES/S).Two- and three-dimensional graphics engines,.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |